Decal Install instructions

BEFORE YOU START: Set Your Walls Up for Success

Great results start with the right prep!
For the best adhesion, ensure your walls are clean, dry, and in good condition.

Freshly painted walls?
Hold off on applying decals for at least 4 weeks to let the paint fully cure and “outgas.” This helps prevent bubbling or peeling.

Wall condition matters:
Smooth, properly painted surfaces work best. If your paint is old, flaky, or wasn’t applied correctly, the decals may not stick as well or could lift over time.

Worried about removal?
Our decals are designed to be removable, but gentle heat (like a hairdryer) can help soften the adhesive and make removal even easier—especially if you're concerned about delicate paint.

Prepare your walls:

• Wash your hands thoroughly.
• Wipe down the wall with a damp microfiber cloth to remove dust and debris.
• Ensure the wall is completely dry before starting.

Unroll and apply:

• Remove your decals from the box and gently roll out the decal sheet until flat.
• Carefully peel away the decal from the backing.
• Place the decal in your desired location on the wall.
• Smooth it down gently with your hands. If the decal folds onto itself, gently pull it apart.
• Use a felt-tipped squeegee or a microfiber cloth-wrapped credit card to smooth the decal from top to bottom, sweeping out any air pockets.
• Use firm, even pressure to ensure the adhesive is pressed evenly onto the wall. The adhesive is pressure-activated, so be careful not to scratch your print.

For larger decals:

• Overlap each piece by approximately 1 cm.
• Align the pattern carefully. If the pattern isn’t lining up from top to bottom, try turning the decal slightly left or right for proper alignment.
• Take your time with this step to ensure a seamless look.

Re-stick as needed:

Feel free to remove and re-stick the decal until you’re happy with the placement.

Our decals are designed to be moved around, so you can adjust them as needed.

Decal features:

Our decals are opaque, suitable for colored walls or overlapping.

Before repositioning, clean your hands and walls again to maintain adhesive strength.

Storage:

Roll up the decal backing for future use if you wish to transport them.

Safe Use Guidelines: Ensure decals are securely applied to prevent peeling. Regularly check decals placed near beds or children's sleeping areas to ensure they remain firmly attached and out of easy reach.

Enjoy transforming your space with your beautiful new decals!

Wall Decal Removal Guide

Wall decals are designed to be removable; however, the condition of your paint may affect the removal process. Follow these steps carefully to minimise any potential damage. Applying heat will help soften the adhesive, making peeling easier and reducing the risk of paint lifting.

Tools You’ll Need:

• Hairdryer or heat gun
• Soft microfibre cloth
• Plastic squeegee or credit card (wrapped in a soft cloth)

Step-by-Step Removal Process

Step 1: Warm Up the Adhesive

1. Plug in your hairdryer and set it to a low to medium heat setting.
2. Hold the dryer 5-10 cm away from one edge of the decal.
3. Slowly move the heat across the decal, warming up the adhesive for about 30 seconds to 1 minute.
4. Avoid using high heat, as it can damage the paint or make the decal brittle.

Step 2: Start Peeling – Go Slow

1. Once the adhesive is warmed, begin peeling from a corner or edge.
2. Use your fingertips or a soft tool (like a cloth-wrapped credit card) to gently lift the edge.
3. Slowly peel the decal back against the wall, keeping it as close to the surface as possible.

Do not pull the decal straight out or at a 90-degree angle, as this may cause the paint to lift. Instead, peel back at a low angle (10-30 degrees) for minimal resistance.

Step 3: Continue Heating & Peeling

1. Move the hairdryer along the decal as you continue peeling.
2. If you feel resistance, pause and reheat the section before proceeding.
3. For large decals, remove them in sections instead of trying to pull off the entire piece at once.

Additional Tips for a Damage-Free Removal

• Avoid yanking or pulling quickly – this increases the risk of paint damage.
• Test a small section first, especially on delicate walls or freshly painted surfaces.
• For stubborn decals, let the heat sit for a little longer before attempting to peel.
• If walls were freshly painted, wait at least four weeks before applying or removing decals to prevent paint damage.

Disclaimer

While our decals are designed to be removable, we cannot guarantee damage-free removal in all cases. The condition of your walls plays a significant role in how well decals adhere and remove. We always advise testing a small area first before proceeding with full removal.

Important Notes

• Avoid applying decals to walls with old, flaky, or improperly applied paint, as this may affect adhesion and durability.
• There is always a risk of paint damage upon removal, especially on low-quality, improperly primed, or freshly painted surfaces.
• If your walls were recently painted, allow at least four weeks for the paint to fully cure before applying decals.
• Using heat (such as a hairdryer) will help loosen the adhesive and minimise potential paint lifting.

By following these recommended removal steps, you can significantly reduce the risk of damage. However, Tiny Walls is not responsible for any wall damage that may occur during decal removal. Always test a small area first before proceeding with full removal.